Learning to Sew – Travel Pillowcase #2

This travel-sized pillowcase has an overlapping back opening to insert the pillow

This travel-sized pillowcase has an overlapping back opening to insert the pillow

Gather Your Tools and Supplies

If you made the pillowcase from the last article, I hope you enjoyed the process while learning how to sew!  This pillowcase is the same size, and takes the same sized pillow insert.  But where the first one had a traditional side opening, this version has an overlapping back opening to insert the pillow.

For this project, you will need: 1/2 yard of cotton fabric, at least 44″ wide, thread to match, and a pillow insert.  You will also need paper or pattern transfer fabric to make your pattern.  Alternately, you can draw the dimensions directly onto the fabric.  For either of these options, you will need a marker or fabric marker, and a straight edge.

You will also need the following sewing tools:  sewing pins, dressmaking shears, pinking shears, a hem gauge, and a seam ripper for those inevitable mistakes.  Small snips or scissors are also handy for cutting threads and other small jobs.

Gather your supplies before you begin

Gather your supplies before you begin

Create Your Pattern and Cut the Fabric

To create the pattern, draw two rectangles onto thin paper or pattern transfer fabric. This special fabric should be located in the interfacing section of your nearest Hancock’s or other fabric store.  (If they don’t have it, a thin inexpensive interfacing would also work.)  One rectangle should be 12″ x 13″ (the pillowcase back), and the other 8.5″ x 13″ (the pillowcase front).  The front is placed on the fold of the fabric on one of the 13″ sides.  The back is placed straight on the grain of the fabric.  (See Learning to Sew – Fabric for details about grainline and straightening fabric)  Draw a horizontal line on the pillowcase back pattern piece parallel with the 13″ side of the rectangle.  Refer to the photo below for all pattern markings.

Mark rectangles as shown here to create a pattern for your pillowcase

Mark rectangles as shown here to create a pattern for your pillowcase

After you have pre-washed and dried your fabric, and straightened at least one end, lay it out flat on the cutting surface.  Lay the pattern pieces out on your fabric as shown below.  Make sure the straight-of-grain arrow on the pillowcase back is parallel to the selvage by measuring the distance between them.  Place the pillowcase front on  the fold where the arrows indicate.  Pin the pattern on the fabric; cut out with dressmaker shears.

Then move the tape measure to the other end of the arrow to make sure the arrow is the same distance at each end

Then move the tape measure to the other end of the arrow to make sure the arrow is the same distance at each end

Measure the distance between one end of the straight-of-grain arrow and the selvage

Measure the distance between one end of the straight-of-grain arrow and the selvage

Pin the pattern pieces on your fabric; cut out carefully with dressmaker shears

Pin the pattern pieces on your fabric; cut out carefully with dressmaker shears

An alternate method of cutting out the pieces of this pillowcase is to draw the rectangles directly onto the fabric.  Use a fabric marker and a straight edge to draw the measurements, taking your time to make sure of your accuracy.  Be sure to draw the 8.5″ by 13″ rectangle on the fold, as shown in the photo below.  Remember, cutting mistakes cannot be corrected like sewing mistakes can.  Place  pins just inside the marked lines to keep the fabric layers from shifting while you cut.  Cut with dressmaker shears.

If you wish, draw the squares directly onto the prepared fabric rather than making a pattern

If you wish, draw the squares directly onto the prepared fabric rather than making a pattern

If you have access to a rotary cutter and mat, you can use these handy tools to cut the pieces of the pillowcase out.  These tools make quick work of straight line cutting, and are very popular with quilters.  If you decide to use a rotary cutter, be sure to practice on some scraps to get the hang of keeping the cutter straight and the straight edge still.

Rotary cutters are very popular with quilters; because you are cutting straight lines, the rotary cutter can be used here as well.

Rotary cutters are very popular with quilters; because you are cutting straight lines, the rotary cutter can be used here as well.

Assemble Your Pillowcase

Now you are ready to assemble your pillowcase.  Remove pins and pattern from the fabric.

To finish the edges of the back opening, turn one 13″ side of the back 1/2″ toward the wrong side, using a hem gauge for accuracy; press.  Turn again, using the last turn as a guide.  My second turn measured 5/8″ in this sample.  Press this turn, then pin for sewing.  Repeat for second back piece.  Sew along the folded edge, taking care to keep your seam as straight as possible.  Be sure to backstitch at the beginning and end of your stitch line to secure the stitches.  Go easy on the foot pedal; this isn’t Nascar!

Turn and press twice; sew along turned edge.  This creates a polished finish for the back opening.

Turn and press twice; sew along turned edge. This creates a polished finish for the back opening.

Unfold the pillowcase front and lay it flat with the right side up.  With right sides together, place one of the backs along the left edge of the front, with the finished edge toward the middle.  Place the other back on the right side, using the same procedure.  The finished edges will overlap about 4.5″.

Place the first back piece as shown, with right sides together and the finished edge toward the middle

Place the first back piece as shown, with right sides together and the finished edge toward the middle

Place the second piece as shown here; pin all around the outside for sewing.

Place the second piece as shown here; pin all around the outside for sewing.

Using a 1/2″ seam allowance, sew all around the outside of the pillowcase. Start on one of the sides, and not on a corner. When you get to a corner you will need to pivot. To do this, stop your stitch when you are 1/2″ away from the corner. Use your hem gauge to be sure of where you should stop. With the needle still down in the fabric, lift the presser foot lever. Turn the fabric for stitching the next side, checking again to be sure you are at 1/2″ for the next seam. Repeat this process at each corner, and stitch until you reach the point where you started. Back stitch here to secure the stitches.  See the short video below for a visual of pivoting.

With pinking shears, trim the outside of the pillowcase.  Take care to only cut the outside raw edge, leaving most of the seam allowance.  Trim the corners diagonally, but do not cut too close to the stitches in the corner.

Cut just the outside edge with pinking shears to keep the raw edges from raveling

Trim the corners diagonally, being careful not to get too close to the stitching line

Trim the corners diagonally, being careful not to get too close to the stitching line

Turn the pillowcase right side out; press. Insert pillow into the back opening and adjust. Stand back and admire your work!

Insert the pillow into the back

Insert the pillow into the back

The back of the pillowcase should look like this when you get the pillow inserted and adjusted

The back of the pillowcase should look like this when you get the pillow inserted and adjusted

If you make this pillowcase, we would sure love to hear about your experience. We’d also love a photo or two, so we can admire your work as well.

Next time, we will tackle a project using a commercial sewing pattern.  Hope you will join us!

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s